Catalogue of damping materials
Key references: Vér & Beranek 2006
Each catalogue has a page of its own: choose another one here and open it, or narrow the rows of this one by name and by the table that printed them.
Seventeen commercial damping treatments, and one thing about them that makes this a different table from the solids catalogue: a loss factor here is not a number. Every loss factor in the solids catalogue is a single figure, because for a metal it hardly moves. For a polymer worked near its glass transition it moves by two orders of magnitude with temperature and with frequency, and the peak is all these pages print. So the peak arrives with three temperatures beside it, one per frequency the table prints a column for: where the material peaks when it is worked at 10 Hz, at 100 Hz and at 1 kHz. A treatment whose peak sits at 20 °C at 100 Hz is doing nothing for you at 100 Hz on a winter morning, and a row read without its temperatures says the opposite of what it holds.
The three storage moduli are the same argument again. One is the stiff end, at low temperature or high frequency, one is the soft end, and one is the modulus that applies in the band where the loss factor peaks, which is the only one of the three that belongs beside the peak. The fourth column is the loss modulus, the imaginary part, which the chapter gives as the product of the other two and is the cheapest check there is on a row. The page is in degrees Fahrenheit and pounds per square inch, so every temperature and every modulus here was converted and is marked as converted, with the page’s figure and its unit beside it. The loss factor is the one column that was not: it has no units, so it is served exactly as printed. The page says in a footnote that the values were read off published curves and that damping data should come from the supplier of the material; three of its cells are corrupted in the printing, are registered in this project’s errata and are left empty here rather than guessed at.
Italic is a value this library worked out; a dotted underline is a cell that is not a plain number, and what it is reads on the cell; an asterisk is a note the page made about the row. Click a mark to read it, or give the table focus and press Enter to walk the marks with the arrow keys.
| Material | Maximum loss factor | Peak at 10 Hz °C | Peak at 100 Hz °C | Peak at 1 kHz °C | Young's modulus, soft end MPa | Young's modulus, stiff end GPa | Young's modulus, transition MPa | Maximum loss modulus MPa | Source |
|---|---|---|---|---|---|---|---|---|---|
| Antiphon-13 | 1.8 | -3.889 | 23.89 | 48.89 | 8.274 | 2.068 | 131 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) | |
| blachford Aquaplas | 0.5 | 10 | 26.67 | 51.67 | 206.8 | 11.03 | 1 517 | 758.4 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| Barry Controls H-326 | 0.8 | -40 | -31.67 | -23.33 | 20.68 | 4.137 | 289.6 | 234.4 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| Dow Corning Sylgard 188 | 0.6 | 15.56 | 26.67 | 43.33 | 2.068 | 0.1517 | 17.93 | 10.34 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| EAR C-1002 | 1.9 | -5 | 12.78 | 32.22 | 1.379 | 2.068 | 53.09 | 103.4 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| EAR C-2003 | 1 | 7.222 | 21.11 | 37.78 | 4.137 | 5.516 | 151.7 | 151.7 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| lord LD-400 | 0.7 | 10 | 26.67 | 51.67 | 22.75 | 20.68 | 689.5 | 482.6 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| Soundcoat DYAD 601 | 1 | -9.444 | 10 | 23.89 | 1.034 | 2.068 | 46.19 | 46.19 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| Soundcoat DYAD 606 | 1 | 21.11 | 37.78 | 54.44 | 0.8274 | 41.37 | 41.37 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) | |
| Soundcoat DYAD 609 | 1 | 51.67 | 65.56 | 85 | 4.137 | 1.379 | 75.84 | 75.84 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| Soundcoat N | 1.5 | -9.444 | -1.111 | 21.11 | 0.4826 | 2.068 | 31.72 | 47.57 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| 3M ISD-110 | 1.7 | 26.67 | 46.11 | 65.56 | 0.2068 | 0.2068 | 6.895 | 11.72 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| 3M ISD-112 | 1.2 | -12.22 | 4.444 | 26.67 | 0.5516 | 0.8963 | 22.06 | 26.89 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| 3M ISD-113 The page prints E_trans = 2.1e2 psi below E_min = 3e2 psi for this row, and footnote c of the same table defines E_min as the smallest value of E. The two cells therefore contradict each other, and the page does not say which of them is wrong: E_I,max = 2.3e2 psi agrees with the printed E_trans through the chapter's own E_I,max = eta_max E_trans, while every other row of the table puts E_trans between one and two orders of magnitude above E_min. Both are served as printed and the defect is registered in docs/ERRATA.md under "Ver & Beranek 2e (2006), TABLE 14.1". | 1.1 | -42.78 | -28.89 | -9.444 | 2.068 | 1.034 | 1.448 | 1.586 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| 3m 468 | 0.8 | -9.444 | 10 | 29.44 | 0.2068 | 0.9653 | 13.79 | 11.03 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| 3M ISD-830 | 1 | -59.44 | -45.56 | -28.89 | 1.034 | 1.379 | 37.92 | 37.92 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
| GE SMRD | 0.9 | 10 | 26.67 | 51.67 | 34.47 | 268.9 | 241.3 | Vér & Beranek 2e TABLE 14.1, PDF page 599 (printed p. 598) |
References
Section titled “References”- Vér, I. L., & Beranek, L. L. (2006). Noise and vibration control engineering: Principles and applications (2nd ed.). Wiley. https://doi.org/10.1002/9780470172568 Table 14.1: the source of the rows of the catalogue of damping materials that cite it.