# Catalogue of predicted scattering coefficients

> One page of the phonometry documentation, as Markdown. Index: https://docs.jmrp.io/phonometry/llms.txt

Canonical: https://docs.jmrp.io/phonometry/reference/catalogues/predicted-scattering-coefficients/
Language: en
Alternate: https://docs.jmrp.io/phonometry/es/reference/catalogues/predicted-scattering-coefficients/index.md
Version: phonometry 4.0.0
Install: pip install "phonometry[full]"
Author: José Manuel Requena Plens (https://orcid.org/0000-0003-1250-6212)
Published: 2026-10-28
Updated: 2026-11-16T21:36:14Z
Summary: Scattering coefficients computed with two- and three-dimensional boundary element models, kept apart from the measured ones, with the solver of each row.

---

The same quantity as the [scattering
coefficients](https://docs.jmrp.io/phonometry/reference/catalogues/scattering-coefficients/) and
not the same kind of number: these were computed with a boundary element model,
and the two are separate catalogues so that a row cannot travel from one to the
other unnoticed.

Cox prints three of them. Two are three-dimensional predictions of 3 m by 3 m
single-plane diffusers, at normal and at random incidence, over the bands from
250 Hz upward, because the book says the coefficient below that should be
taken as zero and prints nothing there. The third is two-dimensional, runs the
whole range, and prints three lines per surface at 0, 56.9 and random
incidence. Each row says which solver produced it.

The book is unusually frank about what they are worth, and the notes on each
table quote it: the coefficient reads absorption as scattering, so the
formulation needs revising for a surface that absorbs; the random incidence
values of the two-dimensional table run high at low frequencies; and the
coefficient reads a redirection as a dispersion, so a 45 degree triangle that
sends a strong reflection straight back scores as if it had scattered.

A note mark after a name or a value points to the note the page makes about that row or cell, listed under the table.

| Surface | Computed with | Angle of incidence (°) | 100 Hz | 125 Hz | 160 Hz | 200 Hz | 250 Hz | 315 Hz | 400 Hz | 500 Hz | 630 Hz | 800 Hz | 1 kHz | 1.25 kHz | 1.6 kHz | 2 kHz | 2.5 kHz | 3.15 kHz | 4 kHz | 5 kHz | Source |
| --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- |
| Sinusoidal cross-section: h = 2 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0.02 | 0.31 | 0.3 | 0.54 | 0.65 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Sinusoidal cross-section: h = 4 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.01 | 0.01 | 0.11 | 0.9 | 0.97 | 0.93 | 0.95 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Sinusoidal cross-section: h = 6 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0 | 0.01 | 0.03 | 0.01 | 0.04 | 0.2 | 0.89 | 0.56 | 0.19 | 1 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Sinusoidal cross-section: h = 8 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0.01 | 0.02 | 0.03 | 0.03 | 0.08 | 0.15 | 0.4 | 0.06 | 0.24 | 0.28 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Sinusoidal cross-section: h = 10 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0.01 | 0.01 | 0.03 | 0.06 | 0.04 | 0.05 | 0.1 | 0.09 | 0.05 | 0.25 | 0.44 | 0.32 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Sinusoidal cross-section: h/L = 20 | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.01 | 0.01 | 0.11 | 0.9 | 0.97 | 0.93 | 0.95 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Triangular cross-section: h = 2 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.22 | 0.21 | 0.39 | 0.47 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Triangular cross-section: h = 4 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0 | 0 | 0.01 | 0 | 0.01 | 0.07 | 0.75 | 0.79 | 0.93 | 0.99 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Triangular cross-section: h = 6 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0 | 0.01 | 0.03 | 0.01 | 0.02 | 0.16 | 1 | 0.88 | 0.47 | 1 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Triangular cross-section: h = 8 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0.01 | 0.02 | 0.02 | 0.03 | 0.02 | 0.05 | 0.18 | 0.67 | 0.26 | 0.13 | 0.57 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Triangular cross-section: h = 10 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.01 | 0.01 | 0.02 | 0.03 | 0.05 | 0.03 | 0.03 | 0.08 | 0.14 | 0.23 | 0.06 | 0.27 | 0.23 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Triangular cross-section: h/L = 25 | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0.01 | 0 | 0.03 | 0.01 | 0.01 | 0.11 | 0.95 | 0.99 | 0.8 | 1 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Rectangular cross-section battens: h = 2 cm, L = 20 cm, w = 10 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.14 | 0.54 | 0.58 | 0.86 | 0.99 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Rectangular cross-section battens: h = 4 cm, L = 20 cm, w = 10 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0.01 | 0.01 | 0.03 | 0.03 | 0.09 | 0.29 | 0.9 | 0.83 | 0.48 | 0.03 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Rectangular cross-section battens: h = 6 cm, L = 20 cm, w = 10 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0.01 | 0.03 | 0.04 | 0.05 | 0.12 | 0.17 | 0.1 | 0.56 | 0.1 | 0.1 | 0.93 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Rectangular cross-section battens: h = 8 cm, L = 20 cm, w = 10 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.01 | 0.01 | 0.04 | 0.08 | 0.04 | 0.11 | 0.17 | 0.1 | 0.05 | 0.06 | 0.2 | 1 | 0.12 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Rectangular cross-section battens: h = 10 cm, L = 20 cm, w = 10 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.05 | 0.04 | 0.13 | 0.06 | 0.08 | 0.14 | 0.11 | 0.05 | 0.02 | 0.3 | 0.98 | 0.22 | 0.71 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Rectangular cross-section battens: h/L = 15 | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0 | 0 | 0.04 | 0.01 | 0.03 | 0.44 | 0.83 | 0.96 | 0.94 | 0.44 |  | Cox & D'Antonio 3e Table C.1, PDF pages 545-546 (printed pp. 488-489) |
| Sinusoidal cross-section: h = 2 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.07 | 0.12 | 0.16 | 0.2 | 0.25 | 0.36 | 0.49 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Sinusoidal cross-section: h = 4 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0.01 | 0.01 | 0.01 | 0.03 | 0.16 | 0.32 | 0.47 | 0.57 | 0.68 | 0.81 | 0.87 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Sinusoidal cross-section: h = 6 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.01 | 0.01 | 0.01 | 0.02 | 0.03 | 0.09 | 0.21 | 0.45 | 0.69 | 0.78 | 0.81 | 0.84 | 0.82 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Sinusoidal cross-section: h = 8 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.01 | 0.02 | 0.03 | 0.05 | 0.08 | 0.12 | 0.23 | 0.49 | 0.74 | 0.71 | 0.72 | 0.78 | 0.8 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Sinusoidal cross-section: h = 10 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.02 | 0.04 | 0.05 | 0.09 | 0.13 | 0.15 | 0.23 | 0.46 | 0.59 | 0.48 | 0.65 | 0.7 | 0.78 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Sinusoidal cross-section: h/L = 35 | three-dimensional boundary element prediction |  |  |  |  |  | 0.09 | 0.08 | 0.09 | 0.11 | 0.05 | 0.1 | 0.22 | 0.48 | 0.75 | 0.79 | 0.79 | 0.81 | 0.82 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Triangular cross-section: h = 2 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.06 | 0.09 | 0.12 | 0.15 | 0.18 | 0.27 | 0.37 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Triangular cross-section: h = 4 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0.01 | 0.01 | 0.01 | 0.02 | 0.15 | 0.26 | 0.38 | 0.47 | 0.56 | 0.71 | 0.82 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Triangular cross-section: h = 6 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.01 | 0.01 | 0.01 | 0.02 | 0.03 | 0.07 | 0.2 | 0.41 | 0.61 | 0.71 | 0.79 | 0.87 | 0.89 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Triangular cross-section: h = 8 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.02 | 0.02 | 0.03 | 0.04 | 0.06 | 0.11 | 0.23 | 0.48 | 0.74 | 0.76 | 0.75 | 0.84 | 0.87 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Triangular cross-section: h = 10 cm, L = 20 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.04 | 0.03 | 0.05 | 0.08 | 0.12 | 0.14 | 0.24 | 0.49 | 0.73 | 0.6 | 0.64 | 0.76 | 0.82 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Triangular cross-section: h/L = 40 | three-dimensional boundary element prediction |  |  |  |  |  | 0.02 | 0.02 | 0.03 | 0.04 | 0.06 | 0.11 | 0.23 | 0.48 | 0.74 | 0.76 | 0.75 | 0.84 | 0.87 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Rectangular cross-section battens: h = 2 cm, L = 20 cm, w = 10 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.08 | 0.19 | 0.32 | 0.42 | 0.47 | 0.72 | 0.82 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Rectangular cross-section battens: h = 4 cm, L = 20 cm, w = 10 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.01 | 0.01 | 0.02 | 0.02 | 0.04 | 0.1 | 0.24 | 0.47 | 0.73 | 0.82 | 0.74 | 0.65 | 0.48 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Rectangular cross-section battens: h = 6 cm, L = 20 cm, w = 10 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.02 | 0.03 | 0.04 | 0.07 | 0.12 | 0.16 | 0.29 | 0.51 | 0.7 | 0.68 | 0.4 | 0.24 | 0.56 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Rectangular cross-section battens: h = 8 cm, L = 20 cm, w = 10 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.03 | 0.04 | 0.07 | 0.13 | 0.15 | 0.19 | 0.29 | 0.44 | 0.46 | 0.39 | 0.31 | 0.63 | 0.6 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Rectangular cross-section battens: h = 10 cm, L = 20 cm, w = 10 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.05 | 0.08 | 0.14 | 0.18 | 0.19 | 0.21 | 0.25 | 0.32 | 0.22 | 0.37 | 0.68 | 0.64 | 0.47 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Rectangular cross-section battens: h/L = 20 | three-dimensional boundary element prediction |  |  |  |  |  | 0.01 | 0.01 | 0.02 | 0.02 | 0.04 | 0.1 | 0.24 | 0.47 | 0.73 | 0.82 | 0.74 | 0.65 | 0.48 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Rectangular cross-section battens: h = 4 cm, L = 20 cm, w → 0 cm (extremely thin) | three-dimensional boundary element prediction |  |  |  |  |  | 0.01 | 0.01 | 0.01 | 0.02 | 0.03 | 0.06 | 0.15 | 0.14 | 0.12 | 0.23 | 0.21 | 0.24 | 0.22 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Rectangular cross-section battens: h = 4 cm, L = 20 cm, w = 5 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.01 | 0.01 | 0.01 | 0.02 | 0.04 | 0.09 | 0.22 | 0.4 | 0.41 | 0.41 | 0.6 | 0.55 | 0.41 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Rectangular cross-section battens: h = 4 cm, L = 20 cm, w = 10 cm[^predictedScattering-1] | three-dimensional boundary element prediction |  |  |  |  |  | 0.01 | 0.01 | 0.02 | 0.02 | 0.04 | 0.1 | 0.24 | 0.47 | 0.73 | 0.82 | 0.74 | 0.65 | 0.48 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Rectangular cross-section battens: h = 4 cm, L = 20 cm, w = 15 cm | three-dimensional boundary element prediction |  |  |  |  |  | 0.01 | 0.01 | 0.01 | 0.02 | 0.03 | 0.06 | 0.2 | 0.4 | 0.69 | 0.7 | 0.6 | 0.46 | 0.36 |  | Cox & D'Antonio 3e Table C.2, PDF pages 547-548 (printed pp. 490-491) |
| Plane surfaces, non-absorbing, any size (any angle) | two-dimensional boundary element prediction | [^predictedScattering-2] | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 1 period, 0.61 m wide (normal) | two-dimensional boundary element prediction | 0 | 0.06 | 0.09 | 0.13 | 0.2 | 0.29 | 0.38 | 0.43 | 0.45 | 0.59 | 0.78 | 0.82 | 0.8 | 0.92 | 0.89 | 0.92 | 0.94 | 0.95 | 0.96 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 1 period, 0.61 m wide (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.27 | 0.24 | 0.23 | 0.26 | 0.32 | 0.45 | 0.69 | 0.79 | 0.8 | 0.92 | 0.88 | 0.91 | 0.9 | 0.9 | 0.91 | 0.92 | 0.94 | 0.96 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 1 period, 0.61 m wide (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.24 | 0.21 | 0.21 | 0.25 | 0.32 | 0.43 | 0.62 | 0.73 | 0.74 | 0.82 | 0.86 | 0.88 | 0.9 | 0.91 | 0.94 | 0.95 | 0.96 | 0.96 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 2 periods, 1.22 m wide (normal) | two-dimensional boundary element prediction | 0 | 0.04 | 0.05 | 0.05 | 0.04 | 0.02 | 0.11 | 0.65 | 0.87 | 0.64 | 0.56 | 0.87 | 0.79 | 0.9 | 0.89 | 0.92 | 0.93 | 0.94 | 0.91 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 2 periods, 1.22 m wide (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.13 | 0.12 | 0.18 | 0.4 | 0.43 | 0.71 | 0.85 | 0.93 | 0.8 | 0.71 | 0.81 | 0.87 | 0.9 | 0.89 | 0.93 | 0.92 | 0.94 | 0.96 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 2 periods, 1.22 m wide (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.16 | 0.16 | 0.21 | 0.32 | 0.34 | 0.52 | 0.8 | 0.93 | 0.76 | 0.67 | 0.88 | 0.87 | 0.91 | 0.91 | 0.93 | 0.94 | 0.95 | 0.95 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 4 periods, 2.44 m wide (normal) | two-dimensional boundary element prediction | 0 | 0.01 | 0 | 0.02 | 0.06 | 0.02 | 0.08 | 0.35 | 0.74 | 0.55 | 0.49 | 0.87 | 0.77 | 0.87 | 0.84 | 0.8 | 0.86 | 0.83 | 0.88 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 4 periods, 2.44 m wide (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.14 | 0.19 | 0.24 | 0.34 | 0.36 | 0.82 | 0.87 | 0.96 | 0.76 | 0.52 | 0.77 | 0.86 | 0.9 | 0.88 | 0.92 | 0.92 | 0.95 | 0.98 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 4 periods, 2.44 m wide (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.21 | 0.22 | 0.24 | 0.29 | 0.3 | 0.53 | 0.78 | 0.93 | 0.71 | 0.56 | 0.87 | 0.86 | 0.9 | 0.88 | 0.9 | 0.93 | 0.94 | 0.94 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 6 periods, 3.66 m wide (normal) | two-dimensional boundary element prediction | 0 | 0 | 0.01 | 0.01 | 0.04 | 0.03 | 0.05 | 0.25 | 0.55 | 0.53 | 0.45 | 0.86 | 0.72 | 0.8 | 0.81 | 0.79 | 0.85 | 0.82 | 0.95 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 6 periods, 3.66 m wide (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.15 | 0.2 | 0.23 | 0.26 | 0.24 | 0.84 | 0.89 | 0.97 | 0.74 | 0.48 | 0.75 | 0.85 | 0.89 | 0.87 | 0.94 | 0.95 | 0.97 | 0.98 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 6 periods, 3.66 m wide (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.22 | 0.23 | 0.24 | 0.26 | 0.26 | 0.52 | 0.76 | 0.91 | 0.68 | 0.51 | 0.86 | 0.85 | 0.89 | 0.88 | 0.9 | 0.94 | 0.94 | 0.95 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 12 periods, 7.32 m wide (normal) | two-dimensional boundary element prediction | 0 | 0 | 0 | 0.01 | 0.02 | 0.02 | 0.03 | 0.13 | 0.33 | 0.48 | 0.4 | 0.86 | 0.76 | 0.84 | 0.87 | 0.83 | 0.81 | 0.87 | 0.9 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 12 periods, 7.32 m wide (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.16 | 0.15 | 0.1 | 0.08 | 0.12 | 0.81 | 0.89 | 0.97 | 0.71 | 0.4 | 0.74 | 0.88 | 0.93 | 0.9 | 0.94 | 0.91 | 0.93 | 0.94 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 1. Effect of changing diffuser width and periodicity, semicylinder(s) non-absorbing surfaces, radius 0.3 m (1 cm flat section between each period): 12 periods, 7.32 m wide (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.23 | 0.22 | 0.21 | 0.2 | 0.19 | 0.48 | 0.73 | 0.87 | 0.64 | 0.46 | 0.86 | 0.86 | 0.89 | 0.87 | 0.89 | 0.92 | 0.92 | 0.91 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 1 cm deep (normal) | two-dimensional boundary element prediction | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.01 | 0.01 | 0.02 | 0.02 | 0.04 | 0.04 | 0.1 | 0.14 | 0.37 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 1 cm deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0 | 0 | 0 | 0 | 0 | 0.01 | 0 | 0 | 0.01 | 0.01 | 0.01 | 0.01 | 0.01 | 0.02 | 0.03 | 0.07 | 0.21 | 0.2 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 1 cm deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0 | 0 | 0 | 0 | 0 | 0.02 | 0.01 | 0.01 | 0.02 | 0.01 | 0.02 | 0.02 | 0.03 | 0.04 | 0.06 | 0.1 | 0.13 | 0.2 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 2 cm deep (normal) | two-dimensional boundary element prediction | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.03 | 0.04 | 0.05 | 0.07 | 0.09 | 0.15 | 0.17 | 0.36 | 0.47 | 0.8 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 2 cm deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0 | 0 | 0 | 0 | 0 | 0.02 | 0.02 | 0.02 | 0.02 | 0.03 | 0.03 | 0.04 | 0.05 | 0.08 | 0.13 | 0.27 | 0.53 | 0.54 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 2 cm deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0 | 0 | 0 | 0 | 0.01 | 0.05 | 0.04 | 0.04 | 0.06 | 0.05 | 0.07 | 0.08 | 0.1 | 0.15 | 0.22 | 0.33 | 0.41 | 0.53 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 5 cm deep (normal) | two-dimensional boundary element prediction | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.06 | 0.2 | 0.23 | 0.33 | 0.4 | 0.51 | 0.67 | 0.77 | 0.86 | 0.84 | 0.92 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 5 cm deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0 | 0 | 0 | 0 | 0.01 | 0.12 | 0.11 | 0.11 | 0.15 | 0.16 | 0.19 | 0.24 | 0.29 | 0.39 | 0.54 | 0.85 | 0.93 | 0.94 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 5 cm deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0 | 0 | 0.01 | 0.01 | 0.06 | 0.16 | 0.16 | 0.18 | 0.22 | 0.25 | 0.31 | 0.38 | 0.47 | 0.59 | 0.71 | 0.8 | 0.82 | 0.85 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 10 cm deep (normal) | two-dimensional boundary element prediction | 0 | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.03 | 0.26 | 0.64 | 0.71 | 0.85 | 0.82 | 0.73 | 0.8 | 0.88 | 0.86 | 0.93 | 0.96 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 10 cm deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0 | 0 | 0 | 0.01 | 0.05 | 0.38 | 0.35 | 0.37 | 0.46 | 0.51 | 0.56 | 0.65 | 0.72 | 0.81 | 0.92 | 0.93 | 0.94 | 0.95 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 10 cm deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.02 | 0.04 | 0.06 | 0.09 | 0.15 | 0.31 | 0.36 | 0.44 | 0.54 | 0.64 | 0.73 | 0.78 | 0.8 | 0.84 | 0.89 | 0.91 | 0.93 | 0.94 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 20 cm deep (normal) | two-dimensional boundary element prediction | 0 | 0 | 0 | 0 | 0.01 | 0.01 | 0.03 | 0.12 | 0.66 | 0.91 | 0.61 | 0.26 | 0.78 | 0.86 | 0.76 | 0.91 | 0.88 | 0.87 | 0.86 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 20 cm deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.03 | 0.04 | 0.06 | 0.09 | 0.19 | 0.75 | 0.76 | 0.88 | 0.87 | 0.81 | 0.7 | 0.72 | 0.85 | 0.92 | 0.91 | 0.96 | 0.97 | 0.98 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 20 cm deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.14 | 0.16 | 0.18 | 0.2 | 0.25 | 0.47 | 0.64 | 0.87 | 0.9 | 0.76 | 0.62 | 0.8 | 0.9 | 0.87 | 0.92 | 0.93 | 0.94 | 0.95 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 30 cm deep (semicylinder) (normal) | two-dimensional boundary element prediction | 0 | 0 | 0.01 | 0.01 | 0.04 | 0.03 | 0.05 | 0.25 | 0.55 | 0.53 | 0.45 | 0.86 | 0.72 | 0.8 | 0.81 | 0.79 | 0.85 | 0.82 | 0.95 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 30 cm deep (semicylinder) (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.15 | 0.2 | 0.23 | 0.26 | 0.24 | 0.84 | 0.89 | 0.97 | 0.74 | 0.48 | 0.75 | 0.85 | 0.89 | 0.87 | 0.94 | 0.95 | 0.97 | 0.98 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 2. Effect of surface depth, 6 semiellipses, non-absorbing, each width 0.6 m, total width 3.66 m (1 cm flat section between semiellipses): 30 cm deep (semicylinder) (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.22 | 0.23 | 0.24 | 0.26 | 0.26 | 0.52 | 0.76 | 0.91 | 0.68 | 0.51 | 0.86 | 0.85 | 0.89 | 0.88 | 0.9 | 0.94 | 0.94 | 0.95 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 3. Triangles, non-absorbing, 3.66 m wide (0.01 cm flat section between each period): 15 periods, 60° (normal) | two-dimensional boundary element prediction | 0 | 0.01 | 0.01 | 0 | 0 | 0 | 0.01 | 0.02 | 0.03 | 0.04 | 0.06 | 0.05 | 0.06 | 0.37 | 0.12 | 0.06 | 0.12 | 0.13 | 0.17 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 3. Triangles, non-absorbing, 3.66 m wide (0.01 cm flat section between each period): 15 periods, 60° (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.49 | 0.6 | 0.68 | 0.71 | 0.58 | 0.19 | 0.18 | 0.33 | 0.25 | 0.45 | 0.23 | 0.27 | 0.68 | 0.65 | 0.95 | 0.92 | 0.93 | 0.98 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 3. Triangles, non-absorbing, 3.66 m wide (0.01 cm flat section between each period): 15 periods, 60° (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.34 | 0.35 | 0.35 | 0.34 | 0.32 | 0.28 | 0.24 | 0.3 | 0.27 | 0.32 | 0.24 | 0.34 | 0.5 | 0.53 | 0.67 | 0.69 | 0.72 | 0.75 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 3. Triangles, non-absorbing, 3.66 m wide (0.01 cm flat section between each period): 9 periods, 45° (normal) | two-dimensional boundary element prediction | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.04 | 0.03 | 0.07 | 0.16 | 0.29 | 0.3 | 0.17 | 0.23 | 0.22 | 0.22 | 0.19 | 0.23 | 0.28 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 3. Triangles, non-absorbing, 3.66 m wide (0.01 cm flat section between each period): 9 periods, 45° (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.03 | 0.04 | 0.06 | 0.07 | 0.08 | 0.2 | 0.54 | 0.95 | 0.99 | 0.75 | 0.93 | 0.97 | 0.99 | 0.99 | 0.99 | 0.99 | 1 | 1 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 3. Triangles, non-absorbing, 3.66 m wide (0.01 cm flat section between each period): 9 periods, 45° (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.15 | 0.17 | 0.19 | 0.21 | 0.23 | 0.28 | 0.37 | 0.59 | 0.8 | 0.79 | 0.69 | 0.82 | 0.83 | 0.87 | 0.89 | 0.9 | 0.9 | 0.91 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 3. Triangles, non-absorbing, 3.66 m wide (0.01 cm flat section between each period): 6 periods, 30° 3.66 m wide (normal) | two-dimensional boundary element prediction | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.02 | 0.06 | 0.36 | 0.96 | 0.98 | 0.81 | 0.99 | 0.89 | 0.97 | 0.97 | 0.99 | 1 | 0.99 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 3. Triangles, non-absorbing, 3.66 m wide (0.01 cm flat section between each period): 6 periods, 30° 3.66 m wide (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.01 | 0.02 | 0.02 | 0.04 | 0.18 | 0.81 | 0.76 | 0.72 | 0.7 | 0.83 | 0.9 | 0.94 | 0.99 | 1 | 0.99 | 0.99 | 1 | 1 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 3. Triangles, non-absorbing, 3.66 m wide (0.01 cm flat section between each period): 6 periods, 30° 3.66 m wide (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.11 | 0.13 | 0.14 | 0.17 | 0.26 | 0.47 | 0.61 | 0.72 | 0.81 | 0.9 | 0.93 | 0.95 | 0.95 | 0.97 | 0.97 | 0.98 | 0.98 | 0.98 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 3. Triangles, non-absorbing, 3.66 m wide (0.01 cm flat section between each period): 3 periods, 18° (normal) | two-dimensional boundary element prediction | 0 | 0 | 0.01 | 0.01 | 0.02 | 0.17 | 0.49 | 0.66 | 0.78 | 0.9 | 0.99 | 0.98 | 0.95 | 0.99 | 0.99 | 0.99 | 0.99 | 0.99 | 0.99 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 3. Triangles, non-absorbing, 3.66 m wide (0.01 cm flat section between each period): 3 periods, 18° (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.01 | 0.1 | 0.37 | 0.42 | 0.37 | 0.39 | 0.43 | 0.51 | 0.59 | 0.71 | 0.82 | 0.94 | 0.98 | 0.94 | 0.94 | 0.98 | 0.97 | 0.98 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 3. Triangles, non-absorbing, 3.66 m wide (0.01 cm flat section between each period): 3 periods, 18° (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.07 | 0.17 | 0.31 | 0.38 | 0.41 | 0.48 | 0.56 | 0.67 | 0.78 | 0.88 | 0.93 | 0.94 | 0.97 | 0.98 | 0.99 | 0.99 | 0.99 | 0.99 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 4. Semiellipses mounted on 3.63 m wide flat baffle, non-absorbing, each semiellipse 0.6 m wide, 0.2 m deep: 1 semiellipse in the middle of baffle (normal) | two-dimensional boundary element prediction | 0 | 0.01 | 0.02 | 0.03 | 0.09 | 0.2 | 0.22 | 0.36 | 0.4 | 0.35 | 0.22 | 0.19 | 0.27 | 0.2 | 0.19 | 0.14 | 0.18 | 0.21 | 0.3 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 4. Semiellipses mounted on 3.63 m wide flat baffle, non-absorbing, each semiellipse 0.6 m wide, 0.2 m deep: 1 semiellipse in the middle of baffle (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.09 | 0.17 | 0.24 | 0.29 | 0.37 | 0.39 | 0.43 | 0.48 | 0.52 | 0.47 | 0.44 | 0.43 | 0.37 | 0.48 | 0.67 | 0.74 | 0.77 | 0.6 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 4. Semiellipses mounted on 3.63 m wide flat baffle, non-absorbing, each semiellipse 0.6 m wide, 0.2 m deep: 1 semiellipse in the middle of baffle (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.15 | 0.22 | 0.28 | 0.32 | 0.38 | 0.42 | 0.47 | 0.51 | 0.53 | 0.48 | 0.44 | 0.46 | 0.48 | 0.49 | 0.5 | 0.53 | 0.52 | 0.54 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 4. Semiellipses mounted on 3.63 m wide flat baffle, non-absorbing, each semiellipse 0.6 m wide, 0.2 m deep: 3 semiellipses with 0.6 m flat sections between (normal) | two-dimensional boundary element prediction | 0 | 0 | 0.01 | 0.03 | 0.05 | 0.26 | 0.72 | 0.88 | 0.89 | 0.7 | 0.46 | 0.53 | 0.65 | 0.63 | 0.58 | 0.51 | 0.66 | 0.68 | 0.76 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 4. Semiellipses mounted on 3.63 m wide flat baffle, non-absorbing, each semiellipse 0.6 m wide, 0.2 m deep: 3 semiellipses with 0.6 m flat sections between (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.03 | 0.17 | 0.52 | 0.62 | 0.56 | 0.66 | 0.78 | 0.8 | 0.9 | 0.95 | 0.94 | 0.72 | 0.54 | 0.72 | 0.9 | 0.8 | 0.91 | 0.91 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 4. Semiellipses mounted on 3.63 m wide flat baffle, non-absorbing, each semiellipse 0.6 m wide, 0.2 m deep: 3 semiellipses with 0.6 m flat sections between (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.13 | 0.22 | 0.38 | 0.5 | 0.57 | 0.67 | 0.79 | 0.85 | 0.85 | 0.76 | 0.69 | 0.75 | 0.77 | 0.75 | 0.79 | 0.85 | 0.81 | 0.78 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 5. Optimized curved surfaces, 3.6 m wide, modulated arrays: 3 periods, 30 cm deep (normal) | two-dimensional boundary element prediction | 0 | 0 | 0.03 | 0.06 | 0.16 | 0.59 | 0.95 | 0.99 | 0.95 | 0.88 | 0.71 | 0.88 | 0.89 | 0.92 | 0.79 | 0.92 | 0.93 | 0.82 | 0.95 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 5. Optimized curved surfaces, 3.6 m wide, modulated arrays: 3 periods, 30 cm deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.05 | 0.31 | 0.74 | 0.76 | 0.7 | 0.68 | 0.85 | 0.88 | 0.92 | 0.95 | 0.94 | 0.89 | 0.94 | 0.96 | 0.95 | 0.99 | 0.97 | 0.99 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 5. Optimized curved surfaces, 3.6 m wide, modulated arrays: 3 periods, 30 cm deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.15 | 0.3 | 0.5 | 0.64 | 0.74 | 0.79 | 0.9 | 0.94 | 0.89 | 0.86 | 0.91 | 0.93 | 0.95 | 0.94 | 0.94 | 0.95 | 0.96 | 0.97 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 5. Optimized curved surfaces, 3.6 m wide, modulated arrays: 6 periods, 20 cm deep (normal) | two-dimensional boundary element prediction | 0 | 0 | 0 | 0 | 0.01 | 0.02 | 0.04 | 0.14 | 0.61 | 0.81 | 0.94 | 0.8 | 0.78 | 0.68 | 0.84 | 0.6 | 0.84 | 0.78 | 0.86 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 5. Optimized curved surfaces, 3.6 m wide, modulated arrays: 6 periods, 20 cm deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.01 | 0.02 | 0.02 | 0.04 | 0.23 | 0.73 | 0.79 | 0.88 | 0.98 | 0.86 | 0.78 | 0.92 | 0.94 | 0.94 | 0.98 | 0.98 | 0.96 | 0.96 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 5. Optimized curved surfaces, 3.6 m wide, modulated arrays: 6 periods, 20 cm deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.09 | 0.11 | 0.14 | 0.16 | 0.27 | 0.48 | 0.68 | 0.85 | 0.94 | 0.89 | 0.8 | 0.86 | 0.9 | 0.93 | 0.89 | 0.94 | 0.95 | 0.94 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 5. Optimized curved surfaces, 3.6 m wide, modulated arrays: 6 periods, 10 cm deep (normal) | two-dimensional boundary element prediction | 0 | 0 | 0 | 0 | 0.01 | 0.01 | 0.02 | 0.07 | 0.15 | 0.23 | 0.3 | 0.38 | 0.82 | 0.86 | 0.8 | 0.89 | 0.73 | 0.9 | 0.89 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 5. Optimized curved surfaces, 3.6 m wide, modulated arrays: 6 periods, 10 cm deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0 | 0.01 | 0.01 | 0.03 | 0.11 | 0.15 | 0.2 | 0.24 | 0.67 | 0.71 | 0.77 | 0.81 | 0.82 | 0.89 | 0.96 | 0.97 | 1 | 0.99 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 5. Optimized curved surfaces, 3.6 m wide, modulated arrays: 6 periods, 10 cm deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.01 | 0.03 | 0.04 | 0.09 | 0.15 | 0.2 | 0.25 | 0.31 | 0.5 | 0.62 | 0.73 | 0.84 | 0.89 | 0.92 | 0.95 | 0.94 | 0.95 | 0.96 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 5. Optimized curved surfaces, 3.6 m wide, modulated arrays: 6 periods, 5 cm deep (normal) | two-dimensional boundary element prediction | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0.01 | 0.02 | 0.03 | 0.04 | 0.13 | 0.49 | 0.62 | 0.8 | 0.9 | 0.93 | 0.9 | 0.91 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 5. Optimized curved surfaces, 3.6 m wide, modulated arrays: 6 periods, 5 cm deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0 | 0 | 0 | 0.01 | 0.01 | 0.02 | 0.02 | 0.04 | 0.31 | 0.39 | 0.42 | 0.42 | 0.43 | 0.52 | 0.69 | 0.81 | 0.93 | 0.95 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 5. Optimized curved surfaces, 3.6 m wide, modulated arrays: 6 periods, 5 cm deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0 | 0.01 | 0.01 | 0.02 | 0.05 | 0.06 | 0.06 | 0.12 | 0.29 | 0.36 | 0.43 | 0.5 | 0.58 | 0.7 | 0.82 | 0.88 | 0.91 | 0.92 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: N = 7 QRD, 6 periods, 0.2 m deep (normal) | two-dimensional boundary element prediction | 0 | 0 | 0.01 | 0.02 | 0.05 | 0.08 | 0.07 | 0.04 | 0.35 | 0.51 | 0.67 | 0.57 | 0.52 | 0.44 | 0.73 | 0.85 | 0.39 | 0.71 | 0.86 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: N = 7 QRD, 6 periods, 0.2 m deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.04 | 0.06 | 0.12 | 0.26 | 0.41 | 0.17 | 0.16 | 0.71 | 0.75 | 0.84 | 0.71 | 0.51 | 0.74 | 0.91 | 0.83 | 0.79 | 0.67 | 0.93 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: N = 7 QRD, 6 periods, 0.2 m deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.12 | 0.15 | 0.19 | 0.27 | 0.36 | 0.3 | 0.25 | 0.69 | 0.78 | 0.72 | 0.69 | 0.51 | 0.66 | 0.86 | 0.82 | 0.69 | 0.7 | 0.88 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: Optimized diffuser, modulated array, 6 periods, 8 wells/period, 0.17 m deep (normal) | two-dimensional boundary element prediction | 0 | 0 | 0.01 | 0.02 | 0.04 | 0.2 | 0.21 | 0.27 | 0.65 | 0.78 | 0.8 | 0.85 | 0.86 | 0.95 | 0.92 | 0.95 | 0.82 | 0.88 | 0.96 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: Optimized diffuser, modulated array, 6 periods, 8 wells/period, 0.17 m deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.03 | 0.07 | 0.11 | 0.22 | 0.4 | 0.43 | 0.55 | 0.58 | 0.76 | 0.9 | 0.74 | 0.89 | 0.95 | 0.96 | 0.94 | 0.96 | 0.96 | 0.97 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: Optimized diffuser, modulated array, 6 periods, 8 wells/period, 0.17 m deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.09 | 0.14 | 0.18 | 0.25 | 0.36 | 0.48 | 0.55 | 0.68 | 0.82 | 0.89 | 0.83 | 0.87 | 0.93 | 0.94 | 0.93 | 0.9 | 0.91 | 0.94 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: N = 7 PRD, 6 periods, 6 wells/period, 0.2 m deep (normal) | two-dimensional boundary element prediction | 0 | 0 | 0.01 | 0.02 | 0.05 | 0.04 | 0.14 | 0.19 | 0.14 | 0.32 | 0.81 | 0.65 | 0.69 | 0.88 | 0.88 | 0.97 | 0.98 | 0.97 | 0.42 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: N = 7 PRD, 6 periods, 6 wells/period, 0.2 m deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.04 | 0.09 | 0.18 | 0.38 | 0.41 | 0.47 | 0.66 | 0.59 | 0.61 | 0.83 | 0.96 | 0.93 | 0.88 | 0.94 | 0.92 | 0.89 | 0.95 | 0.96 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: N = 7 PRD, 6 periods, 6 wells/period, 0.2 m deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.11 | 0.15 | 0.2 | 0.29 | 0.34 | 0.47 | 0.52 | 0.52 | 0.62 | 0.88 | 0.85 | 0.82 | 0.88 | 0.92 | 0.92 | 0.9 | 0.93 | 0.75 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: Diffractal, 1 period, 3 orders of size, N = 7, 0.5 m deep (normal) | two-dimensional boundary element prediction | 0 | 0.16 | 0.45 | 0.28 | 0.39 | 0.7 | 0.85 | 0.87 | 0.83 | 0.73 | 0.79 | 0.89 | 0.86 | 0.96 | 0.96 | 0.89 | 0.84 | 0.91 | 0.9 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: Diffractal, 1 period, 3 orders of size, N = 7, 0.5 m deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.3 | 0.74 | 0.76 | 0.63 | 0.67 | 0.64 | 0.84 | 0.7 | 0.77 | 0.87 | 0.92 | 0.77 | 0.89 | 0.93 | 0.92 | 0.95 | 0.89 | 0.96 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: Diffractal, 1 period, 3 orders of size, N = 7, 0.5 m deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.33 | 0.56 | 0.66 | 0.61 | 0.72 | 0.8 | 0.88 | 0.8 | 0.78 | 0.85 | 0.91 | 0.8 | 0.91 | 0.92 | 0.91 | 0.91 | 0.9 | 0.91 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: Optimized diffuser, 6 period modulated array, 12 wells/period, 0.17 m deep (normal) | two-dimensional boundary element prediction | 0 | 0 | 0.01 | 0.01 | 0.03 | 0.14 | 0.2 | 0.5 | 0.78 | 0.82 | 0.84 | 0.92 | 0.81 | 0.89 | 0.87 | 0.84 | 0.92 | 0.92 | 0.94 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: Optimized diffuser, 6 period modulated array, 12 wells/period, 0.17 m deep (56.9 degrees) | two-dimensional boundary element prediction | 56.9 | 0.04 | 0.08 | 0.13 | 0.24 | 0.5 | 0.7 | 0.67 | 0.9 | 0.92 | 0.92 | 0.95 | 0.88 | 0.91 | 0.96 | 0.97 | 0.99 | 0.98 | 0.98 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |
| 7. Schroeder diffusers, 3.6 m wide: Optimized diffuser, 6 period modulated array, 12 wells/period, 0.17 m deep (random) | two-dimensional boundary element prediction | [^predictedScattering-3] | 0.14 | 0.17 | 0.21 | 0.27 | 0.4 | 0.61 | 0.69 | 0.9 | 0.9 | 0.91 | 0.92 | 0.87 | 0.87 | 0.9 | 0.91 | 0.93 | 0.94 | 0.94 | Cox & D'Antonio 3e Table C.3, PDF pages 549-552 (printed pp. 492-495) |

[^predictedScattering-1]: The page prints this surface twice on one page: it closes the height series of the group and opens the spacing series, with the same thirteen values both times, because it is the reference of both comparisons.
[^predictedScattering-2]: the page prints “All/any” in that column: a plane surface scatters nothing at any angle, so the row stands for all of them
[^predictedScattering-3]: the page prints “Random” in that column: the row is an average over angles of incidence and belongs to no single one

## References

- **Cox, T. J., & D'Antonio, P. (2017).** *Acoustic absorbers and diffusers: Theory, design and application* (3rd ed.). CRC Press. https://doi.org/10.1201/9781315369211
  Tables C.1 to C.3: the source of the rows of the catalogue of predicted scattering coefficients that cite it.
