# Catalogue of ground surfaces

> One page of the phonometry documentation, as Markdown. Index: https://docs.jmrp.io/phonometry/llms.txt

Canonical: https://docs.jmrp.io/phonometry/reference/catalogues/ground-surfaces/
Language: en
Alternate: https://docs.jmrp.io/phonometry/es/reference/catalogues/ground-surfaces/index.md
Version: phonometry 4.0.0
Install: pip install "phonometry[full]"
Author: José Manuel Requena Plens (https://orcid.org/0000-0003-1250-6212)
Published: 2026-10-28
Updated: 2026-11-16T21:36:14Z
Summary: The effective flow resistivity the outdoor propagation models take for a ground, with the model each value was fitted with, and the ground classes A to H.

---

The effective flow resistivity every outdoor propagation model asks the ground
for, which nobody measures on site. It is not the flow resistivity of the soil:
it is the one number that makes a rigid-framed ground model reproduce a
measured attenuation, so it carries the model it was fitted with, and the same
grass fitted three ways is three rows. Eight of these rows are not measured
ground at all but the classes A to H the models define, with the ground factor
ISO 9613-2 and NMPB-2008 each take. Cox prints six of his porosities in per
cent, from 26.9 to 58.1, in a column that states no unit and prints a fraction
on every other row. A porosity of 36.5 is not a porosity, and the page does
not say it is a per cent, so those six cells are empty, and the note on each
quotes the figure the page prints.

Each value is the number its page prints, unless a word in brackets after it says what else it is:

- **approximate**: the page prints it with a tilde
- **range**: the page prints an interval
- **reported**: the page lists several readings
- **unquantified**: the page prints a word here

A note mark after a name or a value points to the note the page makes about that row or cell, listed under the table.

| Surface | Effective flow resistivity (kPa·s/m²) | Porosity | Water content (%) | Porosity decay (1/m) | ISO 9613-2 ground factor | NMPB-2008 ground factor | Source |
| --- | --- | --- | --- | --- | --- | --- | --- |
| Dry snow, newly fallen 0.1 m over about 0.4 m older snow | 10 to 30 (range)[^ground-1] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Sugar snow | 25 to 50 (range)[^ground-2] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Soft forest floor with blueberry greens and moss | 40 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Forest floor covered by weeds | 63 to 100 (range)[^ground-3] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Pine or hemlock forest floor | 20 to 80 (range)[^ground-4] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Soft forest floor covered with pine needles | 160 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Sandy forest floor | 630 to 2 000 (range)[^ground-5] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Dense shrubbery, 20 cm high | 100 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Soil and bark, sparse vegetation | 100 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Peat or turf area, homogeneous organic material | 100 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Soil covered with leaves and twigs | 160 to 250 (range)[^ground-6] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Soil mixed with sawdust | 250 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Relatively dense soil sparsely covered by grass and other low greens | 630 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Short grass, green moss and blueberry greens | 40 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Rough grassland and pasture | 100 to 300 (range)[^ground-7] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Grass, soccer field | 630 to 2 000 (range)[^ground-5] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Lawn, moderately stepped on | 160 to 250 (range)[^ground-6] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Lawn, seldom stepped on | 250 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Lawn | 250 to 400 (range)[^ground-8] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Agricultural field | 160 to 250 (range)[^ground-6] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Hard soil | 400 to 2 000 (range)[^ground-9] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Soil, exposed and rain packed | 4 000 to 8 000 (range)[^ground-10] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Wet, sandy loam | 1 500 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Moistened sand | 500 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Bare sandy plain | 250 to 500 (range)[^ground-11] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Dry sand | 60 to 140 (range)[^ground-12] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Sandy silt, hard packed by vehicles | 800 to 2 500 (range)[^ground-13] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Quarry dust, hard packed by vehicles | 5 000 to 20 000 (range)[^ground-14] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Mixed paving stones and grass | 630 to 2 000 (range)[^ground-5] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Old gravel field with sparse vegetation | 2 000 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Gravel road, stones and dust | 2 000 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Gravel parking lot | 630 to 2 000 (range)[^ground-5] |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Asphalt sealed by dust and light use | 30 000 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Concrete | 20 000 |  |  |  |  |  | Bies 5e Table 5.1, PDF page 256 (printed p. 227) |
| Very soft (snow or moss) | 12.5 |  |  |  | 1 | 1 | Bies 5e Table 5.2, PDF page 257 (printed p. 228) |
| Soft forest floor | 31.5 |  |  |  | 1 | 1 | Bies 5e Table 5.2, PDF page 257 (printed p. 228) |
| Uncompacted, loose ground | 80 |  |  |  | 1 | 1 | Bies 5e Table 5.2, PDF page 257 (printed p. 228) |
| Normal uncompacted ground (pastures, forest floors)[^ground-15] | 200 |  |  |  | 1 | 1 | Bies 5e Table 5.2, PDF page 257 (printed p. 228) |
| Compacted fields, lawns and gravel | 500 |  |  |  | 0 | 0.7 | Bies 5e Table 5.2, PDF page 257 (printed p. 228) |
| Compacted dense ground (gravel road, parking lot)[^ground-16] | 2 000 |  |  |  | 0 | 0.3 | Bies 5e Table 5.2, PDF page 257 (printed p. 228) |
| Asphalt, concrete | 20 000 |  |  |  | 0 | 0 | Bies 5e Table 5.2, PDF page 257 (printed p. 228) |
| Water[^ground-17] | 200 000 |  |  |  | 0 | 0 | Bies 5e Table 5.2, PDF page 257 (printed p. 228) |
| Snow: Dry snow, newly fallen 0.1 m over about 0.4 m older snow[^ground-18] | 10 to 30 (range)[^ground-1] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Snow: Snow[^ground-19] | 5 to 16 (range)[^ground-20] | 0.5 to 0.9 (range)[^ground-21] |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Snow: Sugar snow[^ground-22] | 25 to 50 (range)[^ground-2] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Snow: Snow (new)[^ground-23] | 1 to 10 (range)[^ground-24] | 0.64 to 0.88 (range)[^ground-25] |  | 0 to 3 (range)[^ground-26] |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Snow: Snow (old crusted)[^ground-23] | 8 to 30 (range)[^ground-27] | 0.5 |  | 0 to 100 (range)[^ground-28] |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Snow: Snow (Great Himalaya snowpack)[^ground-19] | 1 to 23 (range)[^ground-29] | 0.52 to 0.89 (range)[^ground-30] |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Forests and crops: In forest, pine, or hemlock[^ground-22] | 20 to 80 (range)[^ground-4] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Forests and crops: Forest floor[^ground-31] | 7 to 200 (range)[^ground-32] | 0.4 to 0.8 (range)[^ground-33] |  | 0 to 40 (range)[^ground-34] |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Forests and crops: Mineral layer beneath mixed deciduous forest[^ground-35] | 540 ± 92 | [^ground-36] | 15 |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Forests and crops: Humus on pine forest floor[^ground-37] | 230 ± 220 | [^ground-38] | 16.1 |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Forests and crops: Litter layer on mixed deciduous forest floor (2–5 cm thick)[^ground-39] | 30 ± 30 |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Forests and crops: Pine forest litter (6–7 cm thick)[^ground-40] | 9 ± 5 | [^ground-41] | 28.6 |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Forests and crops: Tall crops[^ground-42] | 40 to 50 (range)[^ground-43] |  |  | 0 |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Sports field (Fitted using Delany and Bazley model)[^ground-44] | 1 400 | 0.24 |  | -270 |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Sports field (Fitted using semi-phenomenological model)[^ground-45] | 510 |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Sports field (Fitted using variable porosity model)[^ground-46] | 990 |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Lawn (Fitted using Delany and Bazley model)[^ground-47] | 120 to 750 (range)[^ground-48] | 0.34 to 1 (range)[^ground-49] |  | -76 to 47 (range)[^ground-50] |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Lawn (Fitted using semi-phenomenological model)[^ground-45] | 120 to 310 (range)[^ground-51] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Lawn (Fitted using variable porosity model)[^ground-46] | 39 to 370 (range)[^ground-52] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Long grass (Fitted using Delany and Bazley model)[^ground-53] | 47 to 180 (range)[^ground-54] | 0.38 to 1 (range)[^ground-55] |  | -9 to 48 (range)[^ground-56] |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Long grass (Fitted using semi-phenomenological model)[^ground-45] | 37 to 85 (range)[^ground-57] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Long grass (Fitted using variable porosity model)[^ground-46] | 140 to 800 (range)[^ground-58] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Grassland[^ground-59] | 70 to 850, 100 to 240 (reported)[^ground-60] | 0.3 to 0.7 (range)[^ground-61] |  | 0 to 250 (range)[^ground-62] |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Pasture (Fitted using Delany and Bazley model)[^ground-63] | 110 to 1 100 (range)[^ground-64] | 0.2 to 1 (range)[^ground-65] |  | -400 to 80 (range)[^ground-66] |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Pasture (Fitted using semi-phenomenological model)[^ground-45] | 100 to 950 (range)[^ground-67] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Pasture (Fitted using variable porosity model)[^ground-46] | 25 to 820 (range)[^ground-68] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Grass, rough pasture, airport, public buildings, etc.[^ground-69] | 150 to 300 (range)[^ground-70] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Grass: Grass root layer in loamy sand[^ground-71] | 150 ± 90 | [^ground-72] |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Earth, exposed and rain-packed[^ground-22] | 4 000 to 8 000 (range)[^ground-10] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Bare earth (Fitted using Delany and Bazley model)[^ground-73] | 670 | 0.4 |  | -49 |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Bare earth (Fitted using semi-phenomenological model)[^ground-45] | 390 |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Bare earth (Fitted using variable porosity model)[^ground-46] | 370 |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Loose sand or dry cultivated soil[^ground-23] | 30 to 310 (range)[^ground-74] | 0.36 to 0.52 (range)[^ground-75] |  | 0 to 10 (range)[^ground-76] |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Sandy silt, hard packed by vehicles[^ground-77] | 800 to 2 500 (range)[^ground-13] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Arable (Fitted using Delany and Bazley model)[^ground-78] | 93 to 1 900 (range)[^ground-79] | 0.15 to 1 (range)[^ground-80] |  | -490 to 81 (range)[^ground-81] |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Arable (Fitted using semi-phenomenological model)[^ground-45] | 75 to 1 600 (range)[^ground-82] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Arable (Fitted using variable porosity model)[^ground-46] | 22 to 1 700 (range)[^ground-83] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Cultivated soil[^ground-19] | 100 to 2 000 (range)[^ground-84] | 0.4 to 0.6 (range)[^ground-85] |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Wet and compacted soil[^ground-42] | 40 000 |  |  | -200 to 0 (range)[^ground-86] |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Heath (Fitted using semi-phenomenological model)[^ground-87] | 1.7.3 × 10⁵ – 3.2 × 10⁵ (unquantified)[^ground-88] | 0.71 to 1 (range)[^ground-89] |  | 17 to 33 (range)[^ground-90] |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Heath (Fitted using semi-phenomenological model)[^ground-91] | 180 to 260 (range)[^ground-92] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Earth: Heath (Fitted using variable porosity model)[^ground-46] | 51 to 110 (range)[^ground-93] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Rock: Roadside dirt, ill-defined, small rocks up to 0.1 m mesh[^ground-94] | 300 to 800 (range)[^ground-95] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Rock: Clean limestone chops, thick layer (1–2.5 cm mesh)[^ground-96] | 1 000 to 4 000 (range)[^ground-97] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Rock: Old dirt roadway, fine stones (5 cm mesh) interstices filled[^ground-18] | 2 000 to 4 000 (range)[^ground-98] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Rock: Gravel[^ground-99] | 1.5 to 59 (range)[^ground-100] | 0.3 to 0.4 (range)[^ground-101] |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Other: Quarry dust fine, very hard-packed by vehicles[^ground-102] | 5 000 to 20 000 (range)[^ground-14] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Other: Asphalt, sealed by dust and light use[^ground-103] | 30 000 (approximate)[^ground-104] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Other: Porous asphalt, new[^ground-105] | 2 to 15 (range)[^ground-106] | 0.15 to 0.3 (range)[^ground-107] |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Other: Urban (Fitted using Delany and Bazley model)[^ground-108] | 41 to 67 (range)[^ground-109] | 0.61 to 1 (range)[^ground-110] |  | 0 to 25 (range)[^ground-111] |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Other: Urban (Fitted using semi-phenomenological model)[^ground-112] | 35 |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Other: Urban (Fitted using variable porosity model)[^ground-46] | 21 to 67 (range)[^ground-113] |  |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Sand: Coarse sand, pore size 98 μm (water content 0 %)[^ground-114] | 50 |  | 0 | -14 |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Sand: Coarse sand, pore size 98 μm (water content 11 %)[^ground-115] | 100 |  | 11 | -82 |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Sand: Coarse sand, pore size 98 μm (water content 51 %)[^ground-116] | 470 |  | 51 | -141 |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Sand: Coarse sand, pore size 98 μm (water content 95 %)[^ground-117] | 90 |  | 95 | 1 290 |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Sand: Fine sand[^ground-118] | 310 | 0.44 |  |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Sand: Fine sand, pore size 65 μm (water content 0 %)[^ground-114] | 150 |  | 0 | -28 |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Sand: Fine sand, pore size 65 μm (water content 15 %)[^ground-115] | 140 |  | 15 | 130 |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Sand: Fine sand, pore size 65 μm (water content 48 %)[^ground-116] | 150 |  | 48 | 620 |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Sand: Fine sand, pore size 65 μm (water content 95 %)[^ground-119] | 41 |  | 95 | 1 130 |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Sand: Loamy sand[^ground-120] | 420 ± 17 | [^ground-121] | 11.2 |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |
| Sand: Bare sandy plain[^ground-122] | 370 ± 110 | [^ground-123] | 9.3 |  |  |  | Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201) |

[^ground-1]: the page prints 10000 to 30000 and no value
[^ground-2]: the page prints 25000 to 50000 and no value
[^ground-3]: the page prints 63000 to 100000 and no value
[^ground-4]: the page prints 20000 to 80000 and no value
[^ground-5]: the page prints 630000 to 2e+06 and no value
[^ground-6]: the page prints 160000 to 250000 and no value
[^ground-7]: the page prints 100000 to 300000 and no value
[^ground-8]: the page prints 250000 to 400000 and no value
[^ground-9]: the page prints 400000 to 2e+06 and no value
[^ground-10]: the page prints 4e+06 to 8e+06 and no value
[^ground-11]: the page prints 250000 to 500000 and no value
[^ground-12]: the page prints 60000 to 140000 and no value
[^ground-13]: the page prints 800000 to 2.5e+06 and no value
[^ground-14]: the page prints 5e+06 to 2e+07 and no value
[^ground-15]: Description wrapped over two printed lines: "Normal uncompacted ground" / "(pastures, forest floors)".
[^ground-16]: Description wrapped over two printed lines: "Compacted dense ground" / "(gravel road, parking lot)".
[^ground-17]: Class H is water, not a ground surface in the porous sense; the page still gives it a representative flow resistivity, 200000 kPa s/m2, which is an acoustically hard limit rather than a measured value.
[^ground-18]: Name wrapped over two printed lines. Water content, porosity and porosity decay cells all print a dash.
[^ground-19]: The water content and porosity decay cells are blank, not dashed.
[^ground-20]: the page prints 5000 to 16000 and no value
[^ground-21]: the page prints 0.5 to 0.9 and no value
[^ground-22]: Water content, porosity and porosity decay cells all print a dash.
[^ground-23]: Water content cell prints a dash.
[^ground-24]: the page prints 1000 to 10000 and no value
[^ground-25]: the page prints 0.64 to 0.88 and no value
[^ground-26]: the page prints 0 to 3 and no value
[^ground-27]: the page prints 8000 to 30000 and no value
[^ground-28]: the page prints 0 to 100 and no value
[^ground-29]: the page prints 1000 to 23000 and no value
[^ground-30]: the page prints 0.52 to 0.89 and no value
[^ground-31]: Flow resistivity printed "7 × 10^3–20 × 10^4", the two ends written with different exponents. Water content cell prints a dash.
[^ground-32]: the page prints 7000 to 200000 and no value
[^ground-33]: the page prints 0.4 to 0.8 and no value
[^ground-34]: the page prints 0 to 40 and no value
[^ground-35]: Flow resistivity printed "(540 ± 92) × 10^3". Name wrapped over two printed lines. Porosity decay cell prints a dash. The Porosity column prints this value as a number far above 1 while every other row of the column prints a fraction; on the page it is plainly a percentage, but the page does not say so, and the cell is held as misprinted (docs/ERRATA.md).
[^ground-36]: the page prints “36.5” in its Porosity column, which states no unit and prints a fraction on every other row, and a porosity is the open fraction of a volume, so it cannot pass 1. The figure reads as a per cent, but the page does not say so, and this library does not convert a unit the page does not print. The defect is registered in docs/ERRATA.md under “Cox & D'Antonio, Acoustic Absorbers and Diffusers 3e (2017), Table 6.7”.
[^ground-37]: Flow resistivity printed "(230 ± 220) × 10^3"; the stated uncertainty is almost as large as the value. Porosity decay cell prints a dash. The Porosity column prints this value as a number far above 1 while every other row of the column prints a fraction; on the page it is plainly a percentage, but the page does not say so, and the cell is held as misprinted (docs/ERRATA.md).
[^ground-38]: the page prints “58.1” in its Porosity column, which states no unit and prints a fraction on every other row, and a porosity is the open fraction of a volume, so it cannot pass 1. The figure reads as a per cent, but the page does not say so, and this library does not convert a unit the page does not print. The defect is registered in docs/ERRATA.md under “Cox & D'Antonio, Acoustic Absorbers and Diffusers 3e (2017), Table 6.7”.
[^ground-39]: Flow resistivity printed "(30 ± 30) × 10^3"; the stated uncertainty equals the value. Name wrapped over two printed lines, the en dash of "2–5 cm" as printed. Water content, porosity and porosity decay cells all print a dash.
[^ground-40]: Flow resistivity printed "(9 ± 5) × 10^3"; the en dash of "6–7 cm" as printed. Porosity decay cell prints a dash. The Porosity column prints this value as a number far above 1 while every other row of the column prints a fraction; on the page it is plainly a percentage, but the page does not say so, and the cell is held as misprinted (docs/ERRATA.md).
[^ground-41]: the page prints “38.9” in its Porosity column, which states no unit and prints a fraction on every other row, and a porosity is the open fraction of a volume, so it cannot pass 1. The figure reads as a per cent, but the page does not say so, and this library does not convert a unit the page does not print. The defect is registered in docs/ERRATA.md under “Cox & D'Antonio, Acoustic Absorbers and Diffusers 3e (2017), Table 6.7”.
[^ground-42]: Water content and porosity cells print a dash.
[^ground-43]: the page prints 40000 to 50000 and no value
[^ground-44]: First of three fitted values printed for this surface, marked \[a\]. The porosity cell, "0.24", and the porosity decay cell, "−270", are printed once for the surface, on this line, and carry no fit marker. The water content cell is blank.
[^ground-45]: Second of three fitted values printed for this surface, marked \[b\]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.
[^ground-46]: Third of three fitted values printed for this surface, marked \[c\]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.
[^ground-47]: First of three fitted values printed for this surface, marked \[a\]. The porosity cell is printed "0.34–1 \[b\]": the range itself carries the marker \[b\] = Fitted using semi-phenomenological model. The porosity decay cell, printed "−76 to 47", carries no marker. Both are printed once for the surface, on this line. The water content cell is blank.
[^ground-48]: the page prints 120000 to 750000 and no value
[^ground-49]: the page prints 0.34 to 1 and no value
[^ground-50]: the page prints -76 to 47 and no value
[^ground-51]: the page prints 120000 to 310000 and no value
[^ground-52]: the page prints 39000 to 370000 and no value
[^ground-53]: First of three fitted values printed for this surface, marked \[a\]. The porosity cell is printed "0.38–1 \[b\]": the range itself carries the marker \[b\] = Fitted using semi-phenomenological model. The porosity decay cell, printed "−9 to 48", carries no marker. Both are printed once for the surface, on this line. The water content cell is blank.
[^ground-54]: the page prints 47000 to 180000 and no value
[^ground-55]: the page prints 0.38 to 1 and no value
[^ground-56]: the page prints -9 to 48 and no value
[^ground-57]: the page prints 37000 to 85000 and no value
[^ground-58]: the page prints 140000 to 800000 and no value
[^ground-59]: Two flow resistivity ranges are printed on two lines for this one surface, "7 × 10^4–8.5 × 10^5" and "1 × 10^5–2.4 × 10^5", with no fit markers and nothing to pair them with, so both go to reported. Water content cell prints a dash.
[^ground-60]: the page lists 70000 to 850000, 100000 to 240000 and no single value
[^ground-61]: the page prints 0.3 to 0.7 and no value
[^ground-62]: the page prints 0 to 250 and no value
[^ground-63]: First of three fitted values printed for this surface, marked \[a\]. The porosity cell is printed "0.2–1 \[b\]": the range itself carries the marker \[b\] = Fitted using semi-phenomenological model. The porosity decay cell, printed "−400 to 80", carries no marker. Both are printed once for the surface, on this line. The water content cell prints a dash.
[^ground-64]: the page prints 110000 to 1.1e+06 and no value
[^ground-65]: the page prints 0.2 to 1 and no value
[^ground-66]: the page prints -400 to 80 and no value
[^ground-67]: the page prints 100000 to 950000 and no value
[^ground-68]: the page prints 25000 to 820000 and no value
[^ground-69]: Flow resistivity printed "15 × 10^4–30 × 10^4". Name wrapped over two printed lines. Water content, porosity and porosity decay cells all print a dash.
[^ground-70]: the page prints 150000 to 300000 and no value
[^ground-71]: Flow resistivity printed "(150 ± 90) × 10^3" and porosity printed "48 ± 4", the only porosity cell in the table with a stated uncertainty. Water content and porosity decay cells print a dash. The Porosity column prints this value as a number far above 1 while every other row of the column prints a fraction; on the page it is plainly a percentage, but the page does not say so, and the cell is held as misprinted (docs/ERRATA.md).
[^ground-72]: the page prints “48 ± 4” in its Porosity column, which states no unit and prints a fraction on every other row, and a porosity is the open fraction of a volume, so it cannot pass 1. The figure reads as a per cent, but the page does not say so, and this library does not convert a unit the page does not print. The defect is registered in docs/ERRATA.md under “Cox & D'Antonio, Acoustic Absorbers and Diffusers 3e (2017), Table 6.7”.
[^ground-73]: First of three fitted values printed for this surface, marked \[a\]. The porosity cell is printed "0.4 \[b\]": the value itself carries the marker \[b\] = Fitted using semi-phenomenological model. The porosity decay cell, printed "−49", carries no marker. Both are printed once for the surface, on this line. The water content cell is blank.
[^ground-74]: the page prints 30000 to 310000 and no value
[^ground-75]: the page prints 0.36 to 0.52 and no value
[^ground-76]: the page prints 0 to 10 and no value
[^ground-77]: Last row of the table on the first printed page (folio 200, which ends with "(Continued)"). Water content, porosity and porosity decay cells all print a dash.
[^ground-78]: First row of the continuation page (folio 201); the group heading Earth is not repeated there, so the group is carried over from the first page. First of three fitted values printed for this surface, marked \[a\]. The porosity cell is printed "0.15–1 \[b\]": the range itself carries the marker \[b\] = Fitted using semi-phenomenological model. The porosity decay cell, printed "−490 to 81", carries no marker. Both are printed once for the surface, on this line. The water content cell is blank.
[^ground-79]: the page prints 93000 to 1.9e+06 and no value
[^ground-80]: the page prints 0.15 to 1 and no value
[^ground-81]: the page prints -490 to 81 and no value
[^ground-82]: the page prints 75000 to 1.6e+06 and no value
[^ground-83]: the page prints 22000 to 1.7e+06 and no value
[^ground-84]: the page prints 100000 to 2e+06 and no value
[^ground-85]: the page prints 0.4 to 0.6 and no value
[^ground-86]: the page prints -200 to 0 and no value
[^ground-87]: First of three fitted values printed for this surface. TWO defects on the printed line, both transcribed as printed and neither repaired: (1) the low end of the range is printed "1.7.3 × 10^5", with two decimal points, which is not a readable number, so the whole flow resistivity cell goes to unquantified rather than being guessed at; (2) the fit marker is printed \[b\], not \[a\], although every other surface with three fitted lines in this table is marked \[a\], \[b\], \[c\] in that order and the line below is also marked \[b\]. The porosity cell is printed "0.71–1 \[b\]": the range itself carries the marker \[b\] = Fitted using semi-phenomenological model. The porosity decay cell, printed "17–33", carries no marker. Both are printed once for the surface, on this line. The water content cell is blank.
[^ground-88]: the page prints “1.7.3 × 10⁵ – 3.2 × 10⁵” where the number would be
[^ground-89]: the page prints 0.71 to 1 and no value
[^ground-90]: the page prints 17 to 33 and no value
[^ground-91]: Second of three fitted values printed for this surface, marked \[b\]. The line above is marked \[b\] as well; see that row. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.
[^ground-92]: the page prints 180000 to 260000 and no value
[^ground-93]: the page prints 51000 to 110000 and no value
[^ground-94]: Flow resistivity printed "30 × 10^4–80 × 10^4". Name wrapped over two printed lines. Water content, porosity and porosity decay cells all print a dash.
[^ground-95]: the page prints 300000 to 800000 and no value
[^ground-96]: The word "Clean" is printed in italic, the rest of the name upright. Name wrapped over two printed lines. Water content, porosity and porosity decay cells all print a dash.
[^ground-97]: the page prints 1e+06 to 4e+06 and no value
[^ground-98]: the page prints 2e+06 to 4e+06 and no value
[^ground-99]: Flow resistivity printed "1.5 × 10^3–59 × 10^3". Water content and porosity decay cells print a dash.
[^ground-100]: the page prints 1500 to 59000 and no value
[^ground-101]: the page prints 0.3 to 0.4 and no value
[^ground-102]: Flow resistivity printed "5 × 10^6–20 × 10^6". Name wrapped over two printed lines. Water content, porosity and porosity decay cells all print a dash.
[^ground-103]: Flow resistivity printed "≈3 × 10^7" with a printed approximately-equal sign, the only approximate cell in the table. Water content, porosity and porosity decay cells all print a dash.
[^ground-104]: the page prints it with a tilde
[^ground-105]: Flow resistivity printed "2 × 10^3–15 × 10^3". Water content and porosity decay cells print a dash.
[^ground-106]: the page prints 2000 to 15000 and no value
[^ground-107]: the page prints 0.15 to 0.3 and no value
[^ground-108]: First of three fitted values printed for this surface, marked \[a\]. The porosity cell is printed "0.61–1 \[b\]": the range itself carries the marker \[b\] = Fitted using semi-phenomenological model. The porosity decay cell, printed "0–25", carries no marker. Both are printed once for the surface, on this line. The water content cell prints a dash.
[^ground-109]: the page prints 41000 to 67000 and no value
[^ground-110]: the page prints 0.61 to 1 and no value
[^ground-111]: the page prints 0 to 25 and no value
[^ground-112]: Second of three fitted values printed for this surface, marked \[b\]; it is a single value where the other two lines are ranges. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.
[^ground-113]: the page prints 21000 to 67000 and no value
[^ground-114]: First of four. One of four lines printed under this one surface name, one per water content; the water content is the only thing that distinguishes them. Porosity cell prints a dash. The text on folio 215 (PDF page 272) says Horoshenkov and Mohamed found the two-parameter model of Attenborough more suitable for these sands than one based on the Delany and Bazley formulations, and that these are the parameters of that model they deduced.
[^ground-115]: Second of four. One of four lines printed under this one surface name, one per water content; the water content is the only thing that distinguishes them. Porosity cell prints a dash. The text on folio 215 (PDF page 272) says Horoshenkov and Mohamed found the two-parameter model of Attenborough more suitable for these sands than one based on the Delany and Bazley formulations, and that these are the parameters of that model they deduced.
[^ground-116]: Third of four. One of four lines printed under this one surface name, one per water content; the water content is the only thing that distinguishes them. Porosity cell prints a dash. The text on folio 215 (PDF page 272) says Horoshenkov and Mohamed found the two-parameter model of Attenborough more suitable for these sands than one based on the Delany and Bazley formulations, and that these are the parameters of that model they deduced.
[^ground-117]: Fourth of four. One of four lines printed under this one surface name, one per water content; the water content is the only thing that distinguishes them. Porosity cell prints a dash. The flow resistivity falls back at the highest water content, below the 51 % and 11 % lines. The text on folio 215 (PDF page 272) says Horoshenkov and Mohamed found the two-parameter model of Attenborough more suitable for these sands than one based on the Delany and Bazley formulations, and that these are the parameters of that model they deduced.
[^ground-118]: Water content and porosity decay cells print a dash. Printed name is "Fine sand" with no pore size, distinct from the "Fine sand, pore size 65 μm" block below it.
[^ground-119]: Fourth of four. One of four lines printed under this one surface name, one per water content; the water content is the only thing that distinguishes them. Porosity cell prints a dash. The text on folio 215 (PDF page 272) says Horoshenkov and Mohamed found the two-parameter model of Attenborough more suitable for these sands than one based on the Delany and Bazley formulations, and that these are the parameters of that model they deduced.
[^ground-120]: Flow resistivity printed "(420 ± 17) × 10^3". Porosity decay cell prints a dash. The Porosity column prints this value as a number far above 1 while every other row of the column prints a fraction; on the page it is plainly a percentage, but the page does not say so, and the cell is held as misprinted (docs/ERRATA.md).
[^ground-121]: the page prints “37.5” in its Porosity column, which states no unit and prints a fraction on every other row, and a porosity is the open fraction of a volume, so it cannot pass 1. The figure reads as a per cent, but the page does not say so, and this library does not convert a unit the page does not print. The defect is registered in docs/ERRATA.md under “Cox & D'Antonio, Acoustic Absorbers and Diffusers 3e (2017), Table 6.7”.
[^ground-122]: Flow resistivity printed "(370 ± 110) × 10^3". Last row of the table. Porosity decay cell prints a dash. The Porosity column prints this value as a number far above 1 while every other row of the column prints a fraction; on the page it is plainly a percentage, but the page does not say so, and the cell is held as misprinted (docs/ERRATA.md).
[^ground-123]: the page prints “26.9” in its Porosity column, which states no unit and prints a fraction on every other row, and a porosity is the open fraction of a volume, so it cannot pass 1. The figure reads as a per cent, but the page does not say so, and this library does not convert a unit the page does not print. The defect is registered in docs/ERRATA.md under “Cox & D'Antonio, Acoustic Absorbers and Diffusers 3e (2017), Table 6.7”.

## References

- **Bies, D. A., Hansen, C. H., & Howard, C. Q. (2017).** *Engineering noise control* (5th ed.). CRC Press. https://doi.org/10.1201/9781351228152
  Tables 5.1 and 5.2: the source of the rows of the catalogue of ground surfaces that cite it.
- **Cox, T. J., & D'Antonio, P. (2017).** *Acoustic absorbers and diffusers: Theory, design and application* (3rd ed.). CRC Press. https://doi.org/10.1201/9781315369211
  Table 6.7: the source of the rows of the catalogue of ground surfaces that cite it.
